고정밀 세라믹 볼

Steel bearing balls have a ceiling. Spin them fast enough and centrifugal load distorts the raceway. Expose them to moisture and they corrode. Run them in a magnetic or electrical field and they interfere. Push them past 300°C and they lose hardness. 질화규소 (시₃N₄) 세라믹 볼 remove that ceiling entirely. 와 함께 roughly 40% of the density of steel, roughly twice the hardness, and electrical resistivity above 10¹⁴ Ω·cm, Si₃N₄ is the most widely used ceramic rolling element in high-performance bearings—not because it is exotic, but because it solves problems that steel cannot.


주요 특징:

1. 40% Lighter – Lower Centrifugal Load, 더 빠른 속도

Density is the single most consequential difference. Si₃N₄ at 3.2–3.3 g/cm³ is roughly 40% lighter than bearing steel at ~7.8 g/cm³. At high RPM, centrifugal force scales with mass. Lighter balls generate lower centrifugal load on the outer raceway, which reduces skidding, 입다, 그리고 열. This is why hybrid bearings with Si₃N₄ balls can sustain higher n·dm values and accelerate faster at high RPM than all-steel equivalents.

2. ~20% Lower Friction Losses, ~50% Lower Wear Rate

In computational comparisons against M50 steel ball bearings under identical race and lubrication conditions, Si₃N₄ hybrid bearings showed 약 20% lower frictional losses 그리고 wear rates reduced by about 50%. The higher elastic modulus of Si₃N₄ (~300 GPa vs ~208 GPa for steel) reduces elastic hysteresis and micro-slip in the contact zone, contributing to cooler running and longer race life.

3. Electrically Insulating – Eliminates EDM Damage

Si₃N₄ balls have resistivity above 10¹⁴ Ω·cm and act as a stable electrical barrier between shaft and housing. In VFD-driven motors and high-frequency drives, 이것 prevents electrical discharge machining (EDM) fluting damage that destroys steel bearings. Bearing reliability in inverter-fed systems improves dramatically, ~와 함께 mean time between failures often doubling compared with steel bearings.

4. High-Temperature Hardness Retention

Steel bearings begin to soften and lose load capacity above a few hundred degrees. Gas-pressure sintered Si₃N₄ retains usable hardness and strength up to 1100°C (1300°C for hot-pressed grades). This makes Si₃N₄ balls suitable for furnace conveyors, high-temperature pumps, and thermal processing equipment where grease and steel both fail.

5. Non-Magnetic and Corrosion-Resistant

Si₃N₄ is 비자성 and chemically resistant to acids, 알칼리, and humid environments. It will not attract metallic debris, will not distort magnetic fields, and will not corrode in chemical or cleanroom processes. This is essential for semiconductor vacuum equipment, magnetic measurement systems, and chemical dosing pumps.

6. G5 Precision for High-Speed Stability

에이 G5 Si₃N₄ ball holds ball diameter variation and sphericity deviation to 0.13 μm (0.000005″) , with surface roughness Ra ≤ 0.014 μm. At spindle speeds, this level of roundness and finish minimizes vibration, maintains uniform load distribution, and supports surface finish repeatability within 0.2–0.4 µm Ra in precision machining.


응용

  • Hybrid and Full Ceramic Bearings – The dominant application. Si₃N₄ balls paired with steel races (잡종) or ceramic races (전체 세라믹) deliver higher speed, lower friction, and electrical insulation in 공작 기계 스핀들, EV motors, turbomolecular pumps, and dental handpieces.

  • 반도체 및 진공 장비 – 웨이퍼 핸들링, deposition chambers, and high-vacuum pumps. 비자성, 부식 방지, and cleanroom-compatible.

  • Chemical Pumps and Valves – Valve balls, metering pump components, and chemical dosing systems exposed to aggressive media.

  • 고온 기계 – Furnace components, 열처리 설비, and thermal processing equipment operating up to 1100°C.

  • Precision Ball Screws and Measuring Systems – G5 and finer balls for low-friction, high-accuracy linear motion and metrology.

리뷰

아직 리뷰가 없습니다..

가장 먼저 리뷰를 작성해 보세요.5mm Corrosion-resistant Si₃N₄ Silicon Nitride Full Ceramic Balls”

귀하의 이메일 주소는 공개되지 않습니다. 필수 입력란이 표시되어 있습니다