Si₃N₄ Ceramic Balls – Electrically Insulating. Non magnétique, résistant à la corrosion, and capable of hybrid-bearing friction reduction of ~20% with wear rates halved. The definitive rolling element for semiconductor, chimique, and high-speed applications where steel balls fail.
Key Technical Specifications
Steel bearing balls have a ceiling. Spin them fast enough and centrifugal load distorts the raceway. Expose them to moisture and they corrode. Run them in a magnetic or electrical field and they interfere. Push them past 300°C and they lose hardness. Nitrure de silicium (Si₃N₄) boules en céramique remove that ceiling entirely. Avec roughly 40% of the density of steel, roughly twice the hardness, and electrical resistivity above 10¹⁴ Ω·cm, Si₃N₄ is the most widely used ceramic rolling element in high-performance bearings—not because it is exotic, but because it solves problems that steel cannot.
1. 40% Lighter – Lower Centrifugal Load, Vitesse plus élevée
Density is the single most consequential difference. Si₃N₄ at 3.2–3.3 g/cm³ is roughly 40% lighter than bearing steel at ~7.8 g/cm³. At high RPM, centrifugal force scales with mass. Lighter balls generate lower centrifugal load on the outer raceway, which reduces skidding, porter, et de la chaleur. This is why hybrid bearings with Si₃N₄ balls can sustain higher n·dm values and accelerate faster at high RPM than all-steel equivalents.
2. ~20% Lower Friction Losses, ~50% Lower Wear Rate
In computational comparisons against M50 steel ball bearings under identical race and lubrication conditions, Si₃N₄ hybrid bearings showed environ 20% lower frictional losses et wear rates reduced by about 50%. The higher elastic modulus of Si₃N₄ (~300 GPa vs ~208 GPa for steel) reduces elastic hysteresis and micro-slip in the contact zone, contributing to cooler running and longer race life.
3. Electrically Insulating – Eliminates EDM Damage
Si₃N₄ balls have resistivity above 10¹⁴ Ω·cm and act as a stable electrical barrier between shaft and housing. In VFD-driven motors and high-frequency drives, ce prevents electrical discharge machining (GED) fluting damage that destroys steel bearings. Bearing reliability in inverter-fed systems improves dramatically, avec mean time between failures often doubling compared with steel bearings.
4. High-Temperature Hardness Retention
Steel bearings begin to soften and lose load capacity above a few hundred degrees. Gas-pressure sintered Si₃N₄ retains usable hardness and strength up to 1100°C (1300°C for hot-pressed grades). This makes Si₃N₄ balls suitable for furnace conveyors, high-temperature pumps, and thermal processing equipment where grease and steel both fail.
5. Non-Magnetic and Corrosion-Resistant
Si₃N₄ is non magnétique and chemically resistant to acids, alcalis, and humid environments. It will not attract metallic debris, will not distort magnetic fields, and will not corrode in chemical or cleanroom processes. This is essential for semiconductor vacuum equipment, magnetic measurement systems, and chemical dosing pumps.
6. G5 Precision for High-Speed Stability
UN G5 Si₃N₄ ball holds ball diameter variation and sphericity deviation to 0.13 µm (0.000005″) , with surface roughness Ra ≤ 0.014 µm. At spindle speeds, this level of roundness and finish minimizes vibration, maintains uniform load distribution, and supports surface finish repeatability within 0.2–0.4 µm Ra in precision machining.
Hybrid and Full Ceramic Bearings – The dominant application. Si₃N₄ balls paired with steel races (hybride) or ceramic races (entièrement en céramique) deliver higher speed, lower friction, and electrical insulation in broches de machines-outils, EV motors, turbomolecular pumps, and dental handpieces.
Équipements pour semi-conducteurs et vide – Manipulation des plaquettes, deposition chambers, and high-vacuum pumps. Non magnétique, résistant à la corrosion, and cleanroom-compatible.
Chemical Pumps and Valves – Valve balls, metering pump components, and chemical dosing systems exposed to aggressive media.
Machines à haute température – Furnace components, appareils de traitement thermique, and thermal processing equipment operating up to 1100°C.
Precision Ball Screws and Measuring Systems – G5 and finer balls for low-friction, high-accuracy linear motion and metrology.
Envoi...
Avis
Il n'y a pas encore d'avis.